This table represents an SNMP Agent on this device. This parameter when set to 'true' enables the SNMP agent for this device is enabled. The number of entries in the NMStationAccess table. This table controls access to SNMP objects by network management stations. If the table is empty, access to SNMP objects is unrestricted. The objects in this table MUST NOT persist across reboots. Note that it was decided by the WiFi-MGMT working group that SNMP version 3 would not be supported in the standalone router (sRouter). Mechanisms for securing management traffic to/from the sRouter SNMP agent would be handled in a manner different from those provided in SNMP v3. It was also determined that SNMP v2 would offer capabilities sufficent to meet the functional requirements of operators for sRouter manageability use cases. As a result, SNMP version co-existence considerations are not addressed by the sRouter. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for StationAddress. {{nokeys}} Enables or disables the interface. This parameter is based on ''ifAdminStatus'' from {{bibref|RFC2863}}. A non-volatile handle used to reference this instance. {{param}} provides a mechanism for an ACS to label this instance for future reference. An initial unique value MUST be assigned when the CPE creates an instance of this object. The IP address (or subnet) of the network management station. The community string to be matched for access by this entry. If set to a zero-length string, then any community string will match. When read, this object SHOULD return a zero-length string. Specifies the type of access allowed to this network managemtn station. Setting this object to none(1) causes the table entry to be destroyed. Read(2) allows access by 'get' and 'get-next' PDUs. ReadWrite(3) allows access by 'set' as well. RoWithtraps(4), rwWithTraps(5), and trapsOnly(6) control distribution of Trap PDUs transmitted by this device. 1 2 3 4 5 6 This reports Community Public Access capability. This attribute when set to 'true' will indicate that public access is enabled for this device. When set to 'false', indicates public access is disabled for this device. This attribute defines the Topology Mode used for subdividing an Operator-delegated IPv6 prefix. This attribute defines the Router Advertisement (RA) transmission period. The default value is 30 seconds. This attribute when set to 'true' enables the Link-ID feature. The default is 'false'. This attribute when set to 'true' flushes the WiFi settings in non-volatile memory and reinitialize the WiFi system with the new set of values without reboot. This attribute reports a value 'false' when WiFi attributes have been changed but the changes are not active (i.e. not flushed in non-volatile and not part of the active configuration). Systems that support immediate commit upon any attribute change will report this attribute as 'true' always, and silently accepts sets to 'true'. Enables support for the ability to steer a user device to the Private SSID when available. Number of entries in the WifiEventNotif table. This attribute when set to 'true' will indicate that fragmentation is enabled for this SSID. When set to false, indicates fragmentation is disabled for this SSID. Number of entries in the periodic statistics object. This object contains periodic statistics for an 802.11 SSID on a CPE device. Note that these statistics refer to the link layer, not to the physical layer. This object does not include the total byte and packet statistics, which are, for historical reasons, in the parent object. At most one entry in this table can exist with all the same values for IntervalType, Interval and DeviceMACAddress. {{nokeys}} The type of interval for the statistics. Enumeration of: 15-min - Associated SNMP value is 1 1-hour - Associated SNMP value is 2 1-day - Associated SNMP value is 3 {{noenum}} Associated SNMP value is 1 Associated SNMP value is 2 Associated SNMP value is 3 This key indicates the Interval where the measurements were accumulated The interval of measurements is synchronized with the wall clock The total number of intervals is based on a 24 hour period. At an interval of 15 minutes 96 intervals (1..96) are defined, at 30 minutes, 48 intervals (1..48) and 24 intervals (1..24) for 1 hour measurement interval. Devices with no capabilities to report measurements per interval will report the value 0 for the interval attribute of the unique statistics instance. The DeviceMACAddress represents the MAC address of an associated client device. FrameSent is the total number of frames transmitted out of the interface. For conventional 802.11 MAC (a,b,g) this counter corresponds to the total of MSDUs (MAC Service Data Unit) being transmitted. For High Throughput transmissions this corresponds to the A-MSDU (Aggregation MSDU). The value of this counter MAY be reset to zero when the CPE is rebooted. DataFramesSentAck is the total number of MSDU frames marked as duplicates and non duplicates acknowledged. The value of this counter MAY be reset to zero when the CPE is rebooted. DataFramesSentNoAck is the total number of MSDU frames retransmitted out of the interface (i.e., marked as duplicate and non-duplicate) and not acknowledged but not including those defined in dataFramesLost. The value of this counter MAY be reset to zero when the CPE is rebooted. DataFramesLost is the total number of MSDU frames retransmitted out of the interface that where not acknowledged and discarded for reaching max number of retransmissions. The value of this counter MAY be reset to zero when the CPE is rebooted. FramesReceived is the total number of frames received by the interface. For conventional 802.11 MAC (a,b,g) this counter corresponds to the total of MSDUs (MAC Service Data Unit) being transmitted. For High Throughput transmissions (n) this corresponds to A-MSDUs (Aggregation MSDU) and MSDUs. The value of this counter MAY be reset to zero when the CPE is rebooted. DataFramesReceived is the total number of MSDU frames received and marked as non-duplicates. The value of this counter MAY be reset to zero when the CPE is rebooted. DataFramesDuplicateReceived is the total number of duplicated frames received on this interface. The value of this counter MAY be reset to zero when the CPE is rebooted. ProbesReceived is the total number of probes received. ProbesRejected is the total number of probes rejected. The Received Signal Strength indicator is the energy observed at the antenna receiver for a current transmission. The signal to Noise Ratio (SNR) parameter represents the strength of the signal compared to received noise. Disassociations represents the total number of client disassociations. AuthenticationFailures indicates the total number of authentication failures. The LastTimeAssociation parameter represents the last time the client was associated. LastTimeDisassociation parameter represents the last time the client disassociate from the interface. The all zeros value indicates the client is currently associated. The SSIDPolicy object defines the configuration of policies, behaviors and even thresholds controlled per SSID. The BlockAfterAttempts parameter indicates the maximum number of attempts a client is allowed to attempt registration before being denied access. Exceeding this value generates one event. Events from same client should not reoccur more than once an hour. The value zero indicates no connection attempts restrictions. The AllocatedBandwidth parameter indicates the maximum bandwidth reserved for a particular interface. The value zero indicates no limit. The AuthenticationFailures parameter indicates the number of Authenticationfailures a station simultaneously produces to generate the event. Events from same client should not reoccur more than once an hour. The value 0 indicates no threshold and events of this type are not generated. The NonAuthenticatedTraffic parameter represents the number of non-authenticated messages received from a station to generate an event. Events from same client should not reoccur more than once an hour. The value 0 indicates no threshold and events of this type are not generated. The AssociationFailures indicates the number of simultaneous association failures from a station to generate an event. Events from same client should not reoccur more than once an hour. The value 0 indicates no threshold and events of this type are not generated. The StatsInterval parameter indicates the interval value to collect per-interval statistics. The value 0 indicates no interval and values reported are snapshots at the time of the request. The SNR parameter indicates the threshold to report SNR. The value -100 indicates no threshold, and events of this type are not generated. The ANPI parameter indicates the threshold to report the Average Noise plus Interference. The value -100 indicates no threshold, and events of this type are not generated. The LowReceivedPowerThreshold parameter indicates the power level threshold to generate an event whenever the station received power is below the threshold. The value -100 indicates no threshold, and events of this type are not generated. The LowPowerDeniedAccessThreshold parameter indicates the power level threshold to deny client association whenever the station received power is below the threshold. The value -100 indicates no threshold, and events of this type are not generated. The LowerPowerDissasociationThreshold parameter indicates the threshold to report Disassociation due to low power. The Wi-Fi GW should refuse associations when the power level is below this RSSI level. The value -100 indicates no threshold, and events of this type are not generated. The BeaconMcsLevelInUse parameter indicates the beacon MCS to be used. The BeaconMcsLevelsSupported parameter is a list of all the beacon MCSs supported.{{nolist}} This attribute is only applicable to 80+80MHz channels. It sets the second 80MHz channel that does not contain the primary channel indicated by the Channel attribute. The RSSI signal level at which CS/CCA detects a busy condition. This attribute enables APs to increase minimum sensitivity to avoid detecting busy condition from multiple/weak Wi-Fi sources in dense Wi-Fi environments. Indicates the minimum Carrier Sense threshold level supported by the radio. Indicates the maximum Carrier Sense threshold level supported by the radio. This attribute allows configuring the RTS/CTS parameters. Report WIFI Radio Stats Channel Utilization. The fraction of the time AP senses a busy channel or transmits frames. Provides visibility into channel capacity. The FramesRetransmissionsSent parameter indicates the total number of frames retransmitted out of the interface (marked as duplicated). The value of this counter MAY be reset to zero when the CPE is rebooted. The FramesDuplicatedReceived indicates the total number of duplicated frames received on this interface. The value of this counter MAY be reset to zero when the CPE is rebooted. Indicates availability of WiFi SSID data. Enumeration of: None - Associated SNMP value is 1 Requested - Associated SNMP value is 2 Complete - Associated SNMP value is 3 Error - Associated SNMP value is 4 {{noenum}} Associated SNMP value is 1 Associated SNMP value is 2 Associated SNMP value is 3 Associated SNMP value is 4 Number of diagnostic result Entries. Channel number for which the current row's statistics refers. Indicates the frequency band at which the radio this SSID instance is operating. Enumeration of: 2.4GHz - Associated SNMP value is 1 5GHz - Associated SNMP value is 2 {{noenum}} Associated SNMP value is 1 Associated SNMP value is 2 Indicates the bandwidth at which the channel is operating. Enumeration of: 20MHz - Associated SNMP value is 1 40MHz - Associated SNMP value is 2 80MHz - Associated SNMP value is 3 160MHz - Associated SNMP value is 4 {{noenum}} Associated SNMP value is 1 Associated SNMP value is 2 Associated SNMP value is 3 Associated SNMP value is 4 Percentage of total channel bandwidth available for use. Percentage of total channel bandwidth occupied by non-WiFi interface Comma-separated list of strings. Indicates WPS configuration methods supported by the device. Each list item is an enumeration of:  {Microwave, Bluetooth, Radar, Zigbee, etc}. {{nolist}} Configure channel Diagnostic mode and store results in Diagnostic table. Enumeration of: Manual - Run diagnostics one time. Associated SNMP value is 1 Interval - Repeated diagnsotics run at specified interval. Associated SNMP value is 2 Stop - {{noenum}} Run diagnostics one time. Associated SNMP value is 1 Repeated diagnsotics run at specified interval. Associated SNMP value is 2 Stop an active interval-mode diagnostic. Associated SNMP value is 3 Interval between Diagnostics specified in seconds. When set to true, clears Diagnostic results table. The value of this parameter is not part of the device configuration and is always false when read. Maximum number of entries in the table. When the maximum number plus one is reached, the oldest entry, must be deleted. Timestamp in seconds. The position of the sideband in case the bandwidth of the measured service set is 40 MHz. Enumeration of: Lower- Associated SNMP value is 1 Upper - Associated SNMP value is 2 {{noenum}} Associated SNMP value is 1 Associated SNMP value is 2 This attribute is only applicable to 80+80MHz channels. It sets the second 80MHz channel that does not contain the primary channel indicated by the Channel attribute. Configure as private or public (public only if community wifi enabled on device.deviceinfo: 1 - Private, 2 - Public Declare support for Interworking with external networks. Enable/disable Interworking. Enables or disables capability of the access point to interwork with external network. When enabled, the access point includes Interworking IE in the beacon frames. false (0) - Disable, true (1) - Enable Declare Passpoint support Enable/disable Passpoint. false (0) - Disable, true (1) - Enable Total number of active devices associated at any point in time The number of client session entries. The number of client stats entries. The number of Radius settings entries. The number of Access Point Neighbor Stats number of entries. This attribute indicates the number of packets to be retransmitted to have an upper limit. Reports the security mode for the associated device. Enumeration of: None - Associated SNMP value is 1 WEP64 - Associated SNMP value is 2 WEP128 - Associated SNMP value is 3 WPAPersonal - Associated SNMP value is 4 WPA2Personal - Associated SNMP value is 5 WPAWPA2Personal - Associated SNMP value is 6 WPAEnterprise - Associated SNMP value is 7 WPA2Enterprise - Associated SNMP value is 8 WPAWPA2Enterprise - Associated SNMP value is 9 {{noenum}} Associated SNMP value is 1 Associated SNMP value is 2 Associated SNMP value is 3 Associated SNMP value is 4 Associated SNMP value is 5 Associated SNMP value is 6 Associated SNMP value is 7 Associated SNMP value is 8 Associated SNMP value is 9 Encryption Algorithm. Enumeration of: TKIP AES {{noenum}} Reports the status of any known devices that are or have been associated if the CPE tracks device history after disassociation. Enumeration of: Connected - Associated SNMP value is 1 ClientDisassociated - Associated SNMP value is 2 ForcedDisassociationAuth - Associated SNMP value is 3 ForcedDisassociationTimeout - Associated SNMP value is 4 ForcedDisassociationNetMode - Associated SNMP value is 5 ForcedDisassociationSNR - Associated SNMP value is 6 Other - Associated SNMP value is 7 {{noenum}} Associated SNMP value is 1 Associated SNMP value is 2 Associated SNMP value is 3 Associated SNMP value is 4 Associated SNMP value is 5 Associated SNMP value is 6 Associated SNMP value is 7 This Object defines neighbor information known through channel scans. At most one entry in this table can exist with a given value for BSSID. {{nokeys}} The BSSID used for the neighboring AP. The current service set identifier in use by the neighboring WiFi SSID. The value MAY be empty for hidden SSIDs. The CurrentChannel parameter indicates the current channel being used by the neighboring AP. The CurrentBandwidth parameter indicates the current bandwidth in which the neighboring AP is operating. The RSSI parameter indicates the signal strength at which packets from the neighboring AP are received at the measuring AP, in terms of dBm. This Object defines parameters used for filtering by MAC address When set to true, this parameter clear the table from non-volatile memory. The value of this parameter is not part of the device configuration and is always false when read. The number of access control filter entries. This object contains the list of MAC address that will be used for filtering. At most one entry in this table can exist with all the same values for MACAddress. {{nokeys}} This key represents the MAC address of a device to be filtered. ClientSessions object represents the current and closed sessions (association connections). When the maximum number of instances is reached, the oldest closed session instance is replaced by a newly created client association. At most one entry in this table can exist with all the same values for MACAddress. {{nokeys}} The DeviceMACAddress parameter indicates the MAC address of an associated client device. The Start parameter indicates the date and time when the session started. The Stop parameter indicates the date and time when the session ended. If the session is current the value reported is 0001-01-01T00:00:00Z. The TerminationCode parameter indicates the Reason Code or the Status Code that lead to ending the association of the station. Reason code and Status code overlaps. The context of the type of termination is provided by the TerminationMeaning attribute. The value zero indicates the session is active. The TerminationMeaning parameter indicates the meaning of the Reason Code or Status Code for the ended session. The zero-length string is used when the instance corresponds to an active session. The ClientStats object contains accumulative statistics for each client station. A station is reported only after is associated for the first time. At most one entry in this table can exist with all the same values for IntervalType, Interval and DeviceMACAddress. {{nokeys}} The type of interval for the statistics. Enumeration of: 15-min - Associated SNMP value is 1 1-hour - Associated SNMP value is 2 1-day - Associated SNMP value is 3 {{noenum}} Associated SNMP value is 1 Associated SNMP value is 2 Associated SNMP value is 3 The Interval parameter indicate the measurements were accumulated. The interval of measurements is synchronized with the wall clock The total number of intervals is based on a 24 hour period. At an interval of 15 minutes 96 intervals (1..96) are defined, at 30 minutes, 48 intervals (1..48) and 24 intervals (1..24) for 1 hour measurement interval. Devices with no capable to report measurements per interval will report the value 0 for the interval attribute. The DeviceMACAddress parameter indicates the MAC address of an associated client device. The FramesSent parameter indicates the total number of frames transmitted out of the interface. For conventional 802.11 MAC (a,b,g) this counter corresponds to the total of MSDUs (MAC Service Data Unit) being transmitted. For High Throughput transmissions this corresponds to the A-MSDU (Aggregation MSDU) The value of this counter MAY be reset to zero when the CPE is rebooted. The DataFramesSentAck parameter indicates the total number of MSDU frames marked as duplicates and non duplicates acknowledged. The value of this counter MAY be reset to zero when the CPE is rebooted. The DataFramesSentNoAck parameter indicates the total number of MSDU frames retransmitted out of the interface (i.e., marked as duplicate and non- duplicate) and not acknowledged but not including those defined in dataFramesLost. The value of this counter MAY be reset to zero when the CPE is rebooted. The DataFramesLost parameter indicates the total number of MSDU frames retransmitted out of the interface that where not acknowledged and discarded for reaching max number of retransmissions. The value of this counter MAY be reset to zero when the CPE is rebooted. The FramesReceived parameter indicates the total number of frames received by the interface. For conventional 802.11 MAC (a,b,g) this counter corresponds to the total of MSDUs (MAC Service Data Unit) being transmitted. For High Throughput transmissions (n) this corresponds to A-MSDUs (Aggregation MSDU) and MSDUs. The value of this counter MAY be reset to zero when the CPE is rebooted. The DataFramesReceived parameter indicates the total number of MSDU frames received and marked as non-duplicates. The value of this counter MAY be reset to zero when the CPE is rebooted. The DataFramesDuplicateReceived parameter indicates the total number of duplicated frames received on this interface. The value of this counter MAY be reset to zero when the CPE is rebooted. The ProbesReceived parameter indicates the Total number of probes received. The ProbesRejected parameter indicates the total number of probes rejected. The Received Signal Strength Indicator, RSSI, parameter is the energy observed at the antenna receiver for a current transmission. The signal to Noise Ratio (SNR) parameter indicates the signal strength received from a client compared to the noise received. The Disassociations parameter indicates the total number of client disassociations. The AuthenticationFailures parameter indicates the total number of authentication failures. The LastTimeAssociation parameter indicates the Last time the client was associated. The LastTimeDisassociation parameter indicates the last time the client disassociate from the interface. The all zeros value indicates the client is currently associated. MAC layer packet error rate detected and reported by the AP. Reported in errors/second rounding up to the nearest whole number. MAC layer throughput calculated for the interval. Unit of measurement is Kbps. The WEP key 2 expressed as a hexadecimal string. The WEP key 3 expressed as a hexadecimal string. The WEP key 4 expressed as a hexadecimal string. This attribute defines the selected WEP key. This attribute defines a human readable password to derive the WEP keys, following well-known key generation algorithm for this purpose. When this attribute is a zero-length string, WEP keys are used directly. Otherwise, the values of the WEP keys cannot be changed directly and an error on write is returned. This attribute defines the encryption algorithm used for WPA. Enable Management Frame Protection This attribute indicates the failover Radius retry count. This attribute indicates LAN routing is enabled. 'true' indicates LAN Routing is enabled, 'false' otherwise. The Radius Client information for the SSIDs Requiring Radius authentication. The NAS-Identifier parameter corresponds to the Radius attribute NAS-Identifier used in Access request messages. The device always sends the Radius parameter NAS-IP-Address and will send the NAS-Identifier parameter when this attribute is set to other than the zero-length string. The NAS-Identifier attribute can be used as a hint to indicate the authentication server the SSID domain where user tries to authenticate, i.e., when more than one SSID domains are using the same Radius server instance. The LocationPolicy corresponds to the string value of the Radius Basic-Location-Policy-Rules attribute per RFC 5580 The OperatorName parameter corresponds to the string value of the Radius Operator-Name attribute per RFC 5580. The LocationInformation parameter corresponds to the string value of the Radius Location-Information attribute per RFC 5580. The Location Data parameter corresponds to the string value of the Radius LocationData attribute per RFC 5580. The UsageReports parameter indicates whether the client send usage data 'true' or not 'false'. The IntervalInterimReport parameter indicates whether the client send Interim reports at time intervals 'true' or not 'false'. A 'true' value for the APTransitionReport parameter indicates the client sends Interim reports when the stations transitions to a different Access point. A 'true' value for Gigaword Report indicates the client sends Interim reports when the 32-bit counters rollover. Set and report BSS WPS Method (Soft or physical) USBFlashDrive - Associated SNMP value is 1 Ethernet - Associated SNMP value is 2 ExternalNFCToken - Associated SNMP value is 3 IntegratedNFCToken - Associated SNMP value is 4 NFCInterface - Associated SNMP value is 5 PushButton - Associated SNMP value is 6 PIN - Associated SNMP value is 7 Display - Associated SNMP value is 8 Keypad - Associated SNMP value is 9 {{noenum}} Associated SNMP value is 1 Associated SNMP value is 2 Associated SNMP value is 3 Associated SNMP value is 4 Associated SNMP value is 5 Associated SNMP value is 6 Associated SNMP value is 7 Associated SNMP value is 8 Associated SNMP value is 9 BSS WPS Client Pin BSS WPS APP Pin Interworking objects in conjunction with Hotspot2.0 Access Network Type value to be included in the Interworking IE in the beacons. (refer 8.4.2.94 of IEEE Std 802.11-2012). Possible values are: 0 - Private network 1 - Private network with guest access 2 - Chargeable public network 3 - Free public network 4 - Personal device network 5 - Emergency services only network 6-13 - Reserved 14 - Test or experimental 15 - Wildcard Set to true if the network provides connectivity to the Internet; otherwise it is set to false indicating that it is unspecified whether the network provides connectivity to the Internet. Indicates the Venue Group of the Venue Info Field (refer 8.4.1.34 of IEEE Std 802.11-2012) where the access point is installed. 1 - Unspecified 2 - Assembly 3 - Business 4 - Educational 5 -Factory and Industrial 6 - Institutional 7 - Mercantile 8 - Storage 9 - Utility and Miscellaneous 10 - Vehicular 11 - Outdoor 12-255 - Reserved Indicates the Venue Type of the Venue Info Field (refer 8.4.1.34 of IEEE Std 802.11-2012) where the access point is installed. The possible values are listed in the referanced standard. [MACAddress] Homogeneous Extended Service Set Identifier (HESSID). The HESSID is a globally unique identifier that in conjunction with the WLAN-SSID, may be used to provide network identification for a subscription service provider network. Hotspot2.0 EAP method used by this AP. Refer to Device.IEEE8021x. HS Capability List drawn from the following table in exact order. HS Query list (1), HS Capability list (2), Operator Friendly Name (3), WAN Metrics (4), Connection Capability (5), NAI Home Realm Query (6), Operating Class Indication (7), OSU Providers list (8), Reserved (9), Icon Request (10), Icon Binary File (11). Each Octet corresponds to a capability by realitve position as follows: 0-not supported, 1-supported. The OnlineSignupSupported parameter indicates whether online signup is supported 'true' or not 'false'. Downstream Forwarding of Group-Addressed Frames (DGAF) is enabled 'true' or not 'false'. P2P cross connect is enabled 'true' or not 'false'. ANQP Domain ID is a 16-bit field included in Beacon and Probe response frames transmitted by the AP. All APs in the same ESS sharing a common, nonzero value of ANQP Domain ID shall have identical ANQP information for the ANQP elements and Hotspot 2.0 vendor-specific ANQP elements. APs having their ANQP Domain ID field set to a value of zero have unique ANQP information in one or more of their ANQP elements or Hotspot 2.0 vendor-specific ANQP elements, or have not been implemented with means of knowing whether their ANQP information is unique. APs having their ANQP Domain ID field set to -1 should not include ANQP Domain ID field in the HS2.0 indication element. QoS mapping for Interworking Services is enabled 'true' or not 'false'. Additional Step Required for Access (ASRA) is enabled 'true' or not 'false'. The number of venue namaes entries. The number of 3GPP network number entries. The number of consortium entries. The number of doman name entries. He number of operator name entries. The number of NAI realm entries. A table of Venue Names where the access point is installed. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for VenueName. {{nokeys}} Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. A 2 or 3 octet ISO-14962-1997 encoded string field that defines the language used in the Venue Name field. The code value is selected from ISO-639. Indicates the Venue Name where the access point is installed.This additional meta data about the venue is included in the Venue Name ANQP-element. This parameter accepts UTF-8 encoded string represented as hexBinary string. A table of 3GPP Cellular Networks. The table contains Mobile Country Code (MCC) and Mobile Network Code (MNC) of the cellular networks that the access point supports. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for MNC and MCC. {{nokeys}} Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. 3GPP Network Code. 3GPP Country Code A table of Consortium OIs (Organization Identifiers) which are to be transmitted in an ANQP Roaming Consortium ANQP-element. Each entry of this table corresponds to a roaming consortium or single SSP. The first three entries of this table are transmitted in Beacon and Probe response frames. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for OI. {{nokeys}} Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. A IEEE defined public organizationally unique identifier (OUI-24 or OUI-36).it is a UTF-8 formatted character string. NAI Realms corresponding to SSPs sor other entities acccessible via this AP. Supported EAP methods may also be included. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for OSUServerURI. Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. The Domain Name subfield is of variable length and contains a domain name compliant with the “Preferred Name Syntax” as defined in IETF RFC 1035 The Online Signup Object. The number of OSU provider entries. A table of OSU Providers offering Online Sign Up service. This table is included in the OSU Provider sub-field in the OSU Provider List element. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for OSUServerURI. {{nokeys}} Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. The URI of the OSU Server that is used for OSU with the Service Provider indicated in the Names table. It is formatted in accordance with the IETF RFC 3986 A comma seperated list of OSU Method values represented as integers. The methods are listed in the ServiceProvider's preferred order with the most-preferred method first. Possible values (integers) are selected from Table 10 of WFA HS2.0. 0 - OMA-DM 1 - SOAP-XML SPP. All other values (2 - 255) are reserved. Example value "0,1" without quotes. Contains the NAI that is used for OSU with the ServiceProvider indicated in the Names table. OSUNAI is formatted in accordance with IETF RFC 4282. The number of name entries. The number of icon entries. The number of service description entries. A table of OSU Providers Friendly Names that are included in the OSU Provider List element. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for OSUProviderFriendlyName. {{nokeys}} Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. A 2 or 3 octet ISO-14962-1997 encoded string field that defines the language used in the Venue Name field. The code value is selected from ISO-639. Indicates the UTF-8 encoded (represented as hexBinary) OSU Provider Friendly Name in the human language identified by the language code. This parameter accepts UTF-8 encoded string represented as hexBinary string. A table of Icons that are included in the Icons Available subfield of the OSU Provider List element. The Icons Available subfield provides metadata about the OSU provider icon file(s) available for download. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for OSUProviderFriendlyName. {{nokeys}} Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. Indicates the UTF-8 encoded (represented as hexBinary) OSU Provider Friendly Name in the human language identified by the language code. This parameter accepts UTF-8 encoded string represented as hexBinary string. Width in pixels of the OSU Provider icon named by the IconFilename. Height in pixels of the OSU Provider icon named by the IconFilename. A 2 or 3 octet ISO-14962-1997 encoded string field that defines the language used in the Venue Name field. The code value is selected from ISO-639. The IconType is the MIME media type of the binary icon file named by the IconFilename. The IconType field is formatted in accordance with RFC-4288 and its value is selected from the IANA MIME Media Types registered at http://www.iana.org/assignments/media-types/index.html The IconFilename is a UTF-8 encoded field whose value contains the filename of the Icon having the metadata provided in this icon instance. A table of OSU Service Descriptions that are included in the OSUServiceDescription subfield of the OSU Provider List element. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for ServiceDescription. {{nokeys}} Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. A 2 or 3 octet ISO-14962-1997 encoded string field that defines the language used in the Venue Name field. The code value is selected from ISO-639. Indicates the UTF-8 encoded (represented as hexBinary) string containing the ServiceProviders description of the service offering. The Operator Friendly Name element provides zero or more names of operators names who are operating the IEEE 802.11 AN, i.e., the Hotspot Operator. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for OperatorName. {{nokeys}} Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. A 2 or 3 octet ISO-14962-1997 encoded string field that defines the language used in the Venue Name field. The code value is selected from ISO-639. Indicates the Operator Friendly Name of the entity operating the IEEE 802.11 AN i.e. the Hotspot Operator. This parameter accepts UTF-8 encoded string represented as hexBinary string. NAI Realms corresponding to SSPs sor other entities acccessible via this AP. Supported EAP methods may also be included. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for Realm. Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. Indicates NAI Realm Encoding Type used to encode NAI Realm ANQP Element. A value of 0 indicates that the NAI Realm in the NAI Realm subfield is formatted in accordance with IETF RFC4282. A value of 1 indicates that it is a UTF-8 formatted character string. The NAI Realm ANQP-element provides a list of network access identifier (NAI) realms corresponding to SSPs or other entities whose networks or services are accessible via this AP. The number of EAP method entries. A table of EAP Methods that each NAI Realm supports. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for EAPMethod. {{nokeys}} Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. Enumerated value of the The EAP method subfield is a 1-octet subfield that is set to the EAP Type value as given in IANA EAP Method Type Numbers.{{noenum}} The number of authentication parameter entries. Authentication information required by the specified EAP method. At most one entry in this table (regardless of whether or not it is enabled) can exist with a given value for Alias. On creation of a new table entry, the CPE MUST choose an initial value for Alias such that the new entry does not conflict with any existing entries. At most one enabled entry in this table can exist with a given value for ExpandedEAPMethodID. {{nokeys}} Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. The ID subfield is a 1-octet subfield that indicates the type of authentication information provided. 0 - Reserved 1 - Expanded EAP Method 2 - Non-EAP Inner Authentication Type 3 - Inner Authentication EAP Method Type 4 - Expanded Inner EAP Method 5 - Credential Type6 - Tunneled EAP Method Credential Type 6 - Tunneled EAP Method Credential Type 221 - Vendor Specific All other values are reserved. Value encoded in hexBinary (octet string) format as per the section 8.4.4.10 of IEEE 802.11-2012 specification. Hotspot2.0 Reflects the status of the WAN Link. Set to true if the WAN link is at capacity and no additional mobile devices will be permitted to associate to the AP. Otherwise false. An estimate of the WAN backhaul link's current downlink speed in kilobits per second (kbps). The maximum value of this field is 4,294,967,296 kbps (approx. 4.2Tbps). An estimate of the WAN backhaul link's current uplink speed in kilobits per second (kbps). The maximum value of this field is 4,294,967,296 kbps (approx. 4.2Tbps). Current percentage % loading of the downlink WAN connection. Current percentage % loading of the uplink WAN connection. This object represents the Wi-Fi GW notification object. At most one entry in this table can exist with the same values for EventId and TimeStamp. {{nokeys}} This attribute represents the Event Message of the event. The identifier of the event. Date and Time when the event was generated (not the time when the event was dispatched). Authentication information required by the specified EAP method. Enables or disables this object. This parameter is based on ''ifAdminStatus'' from [RFC2863]. A non-volatile handle used to reference this instance. Alias provides a mechanism for an ACS to label this instance for future reference. If the CPE supports the Alias-based Addressing feature as defined in [Section 3.6.1/TR-069] and described in [Appendix II/TR-069], the following mandatory constraints MUST be enforced: Its value MUST NOT be empty. Its value MUST start with a letter. If its value is not assigned by the ACS, it MUST start with a "cpe-" prefix. The CPE MUST NOT change the parameter value. Integer index Number of retries for Radius requests. Radius request timeout in seconds after which the request must be retransmitted for the number of retries available. Default time after which a Wi-Fi client is forced to re-authenticate. Enable or disable caching of PMK. Time interval after which the PMKSA (Pairwise Master Key Security Association) cache is purged. Indicated the number of times a client can unsuccessfully attempt to login within incorrect credentials. When this limit is reached, the client is blacklisted and not allowed to attempt to login to the network. Setting this parameter to 0 (zero) disables the blacklisting feature. Time interval for which a client will continue to be blacklisted one it is marked so. Time interval between identity request retries. A value of o (zero) disables retry interval. The enforced quiet period (time interval) following a failed authentication attempt. A value of 0 (zero) disables quiet period.